Success message
Error message
The mighty Atomic™ Isolated Power Supply is developed to meet the high power requirements of Effectrode tube effects pedals. Includes a unique “soft-start” voltage capability, which eliminates tube heater filament flash and maximize the life of the tubes. Supplied with country-appropriate IEC power cable and four DC power leads.
$469.00
The Atomic™ Isolated Power Supply is specially built to power tube pedals. Tube pedals are much more power-hungry than their solid-state counterparts and require a beefier power to operate properly. This is because of the tube heaters and high voltage operation. To get an idea, take a look at the size of the power transformers inside a vintage or boutique tube amp. The Atomic supplies a massive 6 amps, that’s enough electron juice to power up to four of our tube pedals without compromising tone quality.
High Power: Delivers a colossal 6 Amps (6000mA!) at 12VDC output to power up to four Effectrode pedals.
Configurable: One output can be configured to power 9V center negative pedals.
Operates anywhere in the world from 110-250VAC. No more step up or step down transformers.
Fully isolated outlets completely eliminate earth loop hum.
Short circuit/overload protection protects your tube pedals from damage should they inadvertently be connected reverse polarity (some day all power supplies will be made like this!).
Includes country-appropriate IEC power cable and four DC power leads.
WARNING!!! Disconnect the mains power cable before removing the rear panel of the Atomic power supply. There are hazardous voltages inside this unit which can result in injury or death. If you are uncertain about what you are doing, please seek advice from a properly qualified electrical engineer.
SPECIFICATIONS ARE BELOW THE PHOTO GALLERY
Operates anywhere on planet Earth where 110- 250VAC power is available.
Soft-start: Soft-starts at 6VDC to preheat the tube heaters. This eliminates tube heater filament flash and extends tube life.
Regulated and smoothed: Power output is fully regulated to remove all residual electrical noise.
Includes pedal board mounting brackets.
High Power: Delivers a colossal 6 Amps (6000mA!) at 12VDC output to power up to four Effectrode pedals.
Tough: The electronics are housed in a tough, powder-coated aluminum alloy enclosure with a baked epoxy silkscreen. Built for the road and to withstand the most punishing touring schedule.
Construction: Solid die-cast aluminum alloy
case.
Finish: Tough dark graphite powder coat finish.
The Atomic power supply is compatible with all Effectrode pedals (miniature and subminiature). It’s also been tested with the following pedals by other manufacturers:
Empress Super Delay (12V center +ve)
Redwitch Titan Delay
Providence Chrono Delay (12V center -ve)
Kinglsey Bard (9V)
Vertex Axis Wah (9V)
Chicago Iron Octavian
We’ll keep adding to this list as we and our customers test other pedals out.
Operates anywhere on planet Earth where 110- 250VAC power is available.
Power requirements: 110 – 240VAC @ 60 Watts.
Supplied with IEC mains power cable and 4 × very heavy duty 5.5mm × 2.1mm pedal leads.
4 × isolated 12VDC @ 1250mA outputs (linear regulated and heavily filtered–super quiet).
One of the outputs can be configured to power 9VDC center negative pedals (600mA max.).
Short circuit/overload protection protects tube pedals from damage.
Inches: 7.5"(w) x 4.8"(d) x 1.5"(h)
Weight: 1.25lbs / 0.7kg
Effectrode Thermionic
warrants your pedal to be free from defects in material and workmanship for a period of five years from the original date of purchase.
The tubes, pots, footswitch and power supply are warrantied for a period of ninety days from the original date of purchase.
Feel free to be as specific as you like in your inquiry, or you can wait until we respond.